£ 75 + Parts

Inspection & Adjustment
Cables, Hoses & Hydraulics
Final Quality Assurance
Other

£ 70 + Parts

Inspection & Adjustment
Chain, Cassette & Crankset
Cleaning & Lubrication
Bottom Bracket & Bearings
Other

£ 75 + Parts

Inspection & Assessment
Turing & Tensioning
Hub, Axle & Freehub Service
Tyres, Tubes & Tubeless

£ 70 + Parts

Inspection & Adjustment
Headset Service
Cables, Hoses & Routing
Grips, Bar Tape & Contact Points
Other

£ 70 + Parts

Frame Inspection
Alignment Checks
Hardware, Threads & Mounts
Safety & Structural Assessment
Other

£ 130 + Parts

Inspection & Assessment
Fork Lower Leg Service
Rear Shock Air Can Service
Pivot Bearings & Hardware
Setup & Adjustment
Other

£ 95 + Parts

Inspection & Assessment
Hub Bearings
Bottom Bracket Bearings
Headset Bearings
Suspension Pivot Bearings
Other

Brake system inspected for safe operation and performance.
Brake levers inspected for function, reach, return, and pivot condition.
Brake callipers inspected, cleaned, and aligned.
Brake pistons cleaned and reset.
Brake pads inspected for wear, contamination, and correct fit.
Brake rotors inspected for wear, thickness, heat damage, and condition.
Rotor trueness inspected and corrected where possible.

Brake hoses inspected for wear, damage, leaks, routing, and security.
Hose fittings and connections inspected for leaks and securement.
Mechanical brake cables inspected for fraying, corrosion, and smooth operation.
Hydraulic brake system inspected for pressure consistency and leaks.

Brake performance and safety verification completed
Test ride conducted where safe and applicable.
Final adjustments completed prior to handover.

£37 Each Brake (Labour Only)

Drivetrain system inspected for wear, damage, alignment, and smooth operation.
Front and rear derailleurs inspected for secure mounting and alignment.
Derailleur hanger alignment checked and corrected where required.
Gears indexed, aligned, and tuned for accurate shifting.
Shifters inspected for function, return, and engagement.

Chain inspected for wear and stretch.
Cassette inspected for wear, tooth damage, and engagement.
Chainrings inspected for wear, damage, and secure mounting.
Crankset inspected for secure installation and smooth operation.
Pedals inspected for smooth rotation and secure fit.

Drivetrain components cleaned to remove dirt, grease, and contamination.
Chain cleaned and lubricated with appropriate lubricant.
Derailleur pivot points cleaned and lubricated.
Cassette and chainrings cleaned manually where accessible.

Bottom bracket inspected for play, noise, and smooth rotation.
Crank interface inspected and reinstalled to manufacturer specification.

Final drivetrain function check performed under load.
Test ride conducted where safe and applicable.
Final adjustments completed prior to handover.

Wheels inspected for trueness (lateral and radial), dish, roundness, and overall structural condition.
Rims inspected for wear, damage, cracks, and brake track condition (where applicable).
Spokes and nipples inspected for damage, corrosion, and even tension.
Hubs inspected for smooth rotation, bearing play, and general condition.
Axles and wheel retention systems inspected for secure engagement and correct installation.

Wheel truing performed (minor to moderate lateral and radial correction; severe damage or rebuild quoted separately).
Spoke tension measured and balanced where required.
Wheel dish checked and corrected as necessary.

Hub bearings inspected for wear and smooth operation.
Cup-and-cone hub bearings cleaned, regreased, and adjusted where serviceable.
Sealed hub bearings inspected (replacement quoted separately).
Axle condition inspected; bearing preload set and verified.
Freehub body inspected for function and engagement.
Freehub body cleaned, serviced, and lubricated where applicable.

Tyres inspected for wear, cuts, punctures, and sidewall damage.
Inner tubes inspected and replaced where required (parts additional).
Tyre pressure set appropriately for rider and use.
Tubeless system inspected; setup or sealant refresh performed where required.
Tubeless valves, tape, and sealant inspected and serviced as necessary.

Final wheel alignment, rotation, and comprehensive safety check completed prior to release.
Test ride conducted where safe and applicable.

Cockpit components inspected for damage, wear, and secure installation.
Handlebars inspected for cracks, deformation, and correct positioning.
Stem alignment checked; bolts torqued to manufacturer specification.
Shifter and brake lever position adjusted for rider comfort and control.
Control reach and lever engagement adjusted where applicable.
Bar end plugs inspected and secured.

Headset inspected for play, binding, and smooth rotation.
Headset preload adjusted for correct steering tension.
Headset bearings inspected for wear and contamination.
Headset serviced where accessible (full bearing replacement quoted separately).

Gear cables inspected for fraying, corrosion, and smooth operation.
Brake cables inspected for wear and correct routing (mechanical systems).
Hydraulic hoses inspected for wear, damage, routing, and securement.
Cable and hose routing inspected for correct length, movement, and frame protection.

Grips or bar tape inspected for wear and secure fit.
Saddle alignment checked.
Seatpost clamp torque verified.

Final cockpit alignment and control function check performed.
Safety torque audit of cockpit components completed.
Test ride conducted where safe and applicable.

Frame inspected for cracks, dents, deformation, and visible damage.
High-stress areas inspected (head tube, bottom bracket shell, chainstays, seatstays, welds/junctions).
Frame alignment visually assessed for tracking and symmetry.
Fork inspected for damage, straightness, and correct alignment.

Rear dropout alignment inspected and corrected where possible.
Derailleur hanger alignment checked and corrected using alignment gauge.
Frame and fork tracking checked to ensure proper wheel alignment.

All accessible frame mounting points inspected for damage or wear.
Frame hardware inspected and torqued to manufacturer specification.
Frame threads inspected for damage or contamination (no re-tapping included).
Disc brake mounts inspected for alignment and secure mounting.
Accessory mounts (bottle cages, racks, guards) inspected where fitted.

Comprehensive bolt torque and structural safety check performed.
Frame integrity assessed for continued safe use.
Post-crash inspection available with focused assessment of impact areas.
Technician feedback provided on safety concerns or recommended next steps.

Final alignment and safety verification completed prior to release.
Written condition summary available upon request.

Front and rear suspension inspected for damage, leaks, wear, and smooth operation.
Fork stanchions inspected for scratches, wear, and seal condition.
Rear shock inspected for air loss, damping consistency, and mounting hardware condition.
Suspension bushings, mounts, and hardware inspected for play and wear.

Fork lower legs removed and serviced.
Lower-leg internals cleaned and inspected.
Dust seals and foam rings cleaned and lubricated.
Fresh suspension lubricant installed to manufacturer specification.
Fork reassembled and function-tested.

Rear shock air can removed and serviced.
Air can seals inspected, cleaned, and lubricated.
Air can reassembled and pressure restored to specification.

(Does not include full damper rebuild unless quoted separately.)

Suspension pivot bearings inspected for play and smooth operation.
Pivot hardware inspected for wear or damage.
Suspension pivot bolts torqued to manufacturer specification.
Pivot bearing replacement available where required (parts additional).

Suspension air pressure set for rider weight.
Sag measured and adjusted (front and rear).
Rebound and compression settings adjusted to baseline or rider preference.
Rider setup guidance provided where applicable.

Final suspension function and safety check completed prior to release.
Test ride performed to confirm correct suspension operation (where safe and applicable).

Bearings inspected for wear, contamination, corrosion, play, and smooth rotation.
Bearing preload and alignment assessed where applicable.
Noise, roughness, and rotational resistance evaluated.

Hub bearings inspected for smooth rotation and correct preload.
Cup-and-cone hub bearings cleaned, regreased, and adjusted where serviceable.
Sealed hub bearings inspected (replacement quoted separately).
Axle condition inspected; preload set and verified.

Bottom bracket inspected for play, noise, and smooth rotation.
Bottom bracket removed where required for inspection.
Bearings cleaned and regreased where serviceable.
Bottom bracket reinstalled and torqued to manufacturer specification.
Replacement available where required (parts additional).

Headset inspected for play, binding, and smooth rotation.
Headset bearings removed, cleaned, and regreased where serviceable.
Headset reassembled and adjusted for correct preload and alignment.
Replacement available where required (parts additional).

Suspension pivot bearings inspected for play and smooth movement.
Pivot hardware inspected and torqued to specification.
Pivot bearing replacement available where required (parts additional).

(Full pivot bearing replacement labour quoted separately.)

Final bearing preload and safety check completed prior to release.
Test ride performed where safe and applicable.

My Cart

Brake Service

Drivetrain Service

Wheel Service

Cockpit Service

Frame Service

Suspension Service

Bearing Service

Brake system inspected for safe operation and performance.

Brake levers inspected for function, reach, return, and pivot condition.

Brake callipers inspected, cleaned, and aligned.

Brake pistons cleaned and reset.

Brake pads inspected for wear, contamination, and correct fit.

Brake rotors inspected for wear, thickness, heat damage, and condition.

Rotor trueness inspected and corrected where possible.

Brake hoses inspected for wear, damage, leaks, routing, and security.

Hose fittings and connections inspected for leaks and securement.

Mechanical brake cables inspected for fraying, corrosion, and smooth operation.

Hydraulic brake system inspected for pressure consistency and leaks.

Brake performance and safety verification completed

Test ride conducted where safe and applicable.

Final adjustments completed prior to handover.

£37 Each Brake (Labour Only)

Drivetrain system inspected for wear, damage, alignment, and smooth operation.

Front and rear derailleurs inspected for secure mounting and alignment.

Derailleur hanger alignment checked and corrected where required.

Gears indexed, aligned, and tuned for accurate shifting.

Shifters inspected for function, return, and engagement.

Chain inspected for wear and stretch.

Cassette inspected for wear, tooth damage, and engagement.

Chainrings inspected for wear, damage, and secure mounting.

Crankset inspected for secure installation and smooth operation.

Pedals inspected for smooth rotation and secure fit.

Drivetrain components cleaned to remove dirt, grease, and contamination.

Chain cleaned and lubricated with appropriate lubricant.

Derailleur pivot points cleaned and lubricated.

Cassette and chainrings cleaned manually where accessible.

Bottom bracket inspected for play, noise, and smooth rotation.

Crank interface inspected and reinstalled to manufacturer specification.

Final drivetrain function check performed under load.

Test ride conducted where safe and applicable.

Final adjustments completed prior to handover.

Wheels inspected for trueness (lateral and radial), dish, roundness, and overall structural condition.

Rims inspected for wear, damage, cracks, and brake track condition (where applicable).

Spokes and nipples inspected for damage, corrosion, and even tension.

Hubs inspected for smooth rotation, bearing play, and general condition.

Axles and wheel retention systems inspected for secure engagement and correct installation.

Wheel truing performed (minor to moderate lateral and radial correction; severe damage or rebuild quoted separately).

Spoke tension measured and balanced where required.

Wheel dish checked and corrected as necessary.

Hub bearings inspected for wear and smooth operation.

Cup-and-cone hub bearings cleaned, regreased, and adjusted where serviceable.

Sealed hub bearings inspected (replacement quoted separately).

Axle condition inspected; bearing preload set and verified.

Freehub body inspected for function and engagement.

Freehub body cleaned, serviced, and lubricated where applicable.

Tyres inspected for wear, cuts, punctures, and sidewall damage.

Inner tubes inspected and replaced where required (parts additional).

Tyre pressure set appropriately for rider and use.

Tubeless system inspected; setup or sealant refresh performed where required.

Tubeless valves, tape, and sealant inspected and serviced as necessary.

Final wheel alignment, rotation, and comprehensive safety check completed prior to release.

Test ride conducted where safe and applicable.

Cockpit components inspected for damage, wear, and secure installation.

Handlebars inspected for cracks, deformation, and correct positioning.

Stem alignment checked; bolts torqued to manufacturer specification.

Shifter and brake lever position adjusted for rider comfort and control.

Control reach and lever engagement adjusted where applicable.

Bar end plugs inspected and secured.

Headset inspected for play, binding, and smooth rotation.

Headset preload adjusted for correct steering tension.

Headset bearings inspected for wear and contamination.

Headset serviced where accessible (full bearing replacement quoted separately).

Gear cables inspected for fraying, corrosion, and smooth operation.

Brake cables inspected for wear and correct routing (mechanical systems).

Hydraulic hoses inspected for wear, damage, routing, and securement.

Cable and hose routing inspected for correct length, movement, and frame protection.

Grips or bar tape inspected for wear and secure fit.

Saddle alignment checked.

Seatpost clamp torque verified.